公司新聞

水穩攪拌站進行空氣處理組件時會如何？

來源：http://www.piao.sd.cn/ 日期：2022-04-25

　　混凝土生產過程中存在的浪費，主要是混凝土攪拌站生產人員沒法掌握車輛攪拌罐中實際物料的質量，這也是水穩攪拌站發揮作用的時候。那水穩攪拌站進行空氣處理組件時會如何？

　　The waste in the production process of concrete is mainly that the production personnel of concrete mixing station can not master the quality of the actual material in the vehicle mixing tank, which is also the time when the water stable mixing station plays a role. What about the water stable mixing plant for air treatment components?

　　油水分離器的故障中又分為，濾芯堵塞、破損，排污閥的運動部件動件不靈活等情況。工作中要經常清洗濾芯，除去排污器內的油污和雜質。濟南水穩攪拌站調壓閥的故障與上述“減壓閥的故障”相同。油霧器的故障現象有：不滴油、油杯底部沉積有水分、油杯口的密封圈損壞等。

　　The faults of oil-water separator can be divided into blockage and damage of filter element, inflexible moving parts of sewage valve and so on. Work often to clean the filter, remove the oil pollution and impurities in the sewage. The failure of the pressure regulating valve of Ji 'nan water stability mixing plant is the same as the above “failure of the pressure reducing valve”. The fault phenomena of oil mist include: no oil dripping, water deposition at the bottom of the oil cup, damage of the sealing ring at the mouth of the oil cup, etc.

　　當油霧器不滴油時，應檢查進氣口的氣流量是否低于起霧流量，是否漏氣，油量調節針閥是否堵塞等；如果油杯底部沉積了水分，應及時排除；當密封圈損壞時，應及時更換。由于氣缸裝配不當和長期使用，氣動執行元件（氣缸）易發生內、外泄漏，輸出力不足和動作不平穩，緩沖效果不好，活塞桿和缸蓋損壞等故障現象。

　　When the oil mist does not drop oil, it should be checked whether the air flow of the air inlet is lower than the fog flow, whether the air leakage, oil regulating needle valve is blocked, etc.; If water is deposited at the bottom of the oil cup, it should be removed in time; When the sealing ring is damaged, it should be replaced in time. Due to improper cylinder assembly and long-term use, pneumatic actuator （cylinder） prone to internal and external leakage, insufficient output force and action is not smooth, the buffer effect is not good, piston rod and cylinder head damage and other fault phenomena.

　　濟南水穩攪拌站壓力調不高，往往是因調壓彈簧斷裂或膜片破裂而造成的，需要換掉；壓力上升緩慢，一般是因過濾網被堵塞引起的，應拆下清洗。管路接頭泄漏和軟管破裂時可從聲音上來判斷漏氣的部位，應及時修補或更換。

　　Ji 'nan water stability mixing station pressure is not high, often due to pressure spring fracture or diaphragm rupture caused by the need to replace; The pressure rises slowly, generally because the filter is blocked, should be removed and cleaned. When the pipe joint leaks or the hose breaks, you can determine the air leakage part by the sound, and repair or replace it in time.

　　水穩攪拌站進行空氣處理組件時會如何？以上便是問題的講解內容了，如果您還有其他問題就來網站www.piao.sd.cn進行咨詢吧！

　　How will the water stable mixing plant handle the air components? The above is the explanation of the problem content, if you have other questions to consult the website www.piao.sd.cn!

上一條：濟南攤鋪機施工前的準備工作要做好！

下一條：裝載機租賃維修有四大問題要了解